Spark & Co Logo


The Vision 300’s heat symmetric basic frame structure with a high-grade cast iron base ensures twist rigidity against spindle head motion. Its structure guarantees a reduction in thermal displacement, leading to a balance of high-rigidity and a reduced weight as a response. The two horizontally opposed flat linear motors equipped with powerful magnets ensure clearance in the side-ways, canceling out any attraction forces.

The system’s dual-layer cooling system combines direct forced oil cooling with a wide-range jacket to separate the spindle head from the casting. Leading to complete heat isolation, the double cooling system positioned between the heat generating coils is matched by an in-line oil chiller unit to ensure complete control of the coolant temperature. Hot air will never collect at the spindle thanks to the Vision 300’s centralized exhaust and outside airflow system.

High-quality builder Roku-Roku incorporated cutting-edge technology into its Vision 300 system, ultimately designing a well-built machine to ensure precise application and optimized velocity performance. The specialty machine tool builder implemented its Super PC III that can be set to one of 3 different modes to meet any machining requirements into the Vision 300. That level of customization, plus features including Fanuc’s Digital Intelligent Servo System with five-place decimal input and feedback, contribute to the Vision 300’s unsurpassed speed and accuracy despite even the most complex contours.


Machine Travels X x Y x Z: in (mm)
16.0 x 13.0 x 7.9
Spindle Speed
3,000 ~ 36,000 RPM
Spindle HP
Spindle Lubrication
Grease Packed
Tool Changer Size
20 Position Standard
Positioning Accuracy/Repeatability: in (μm)
±0.000040/±0.000012 (±1.0/±0.3)
Table Work Area X x Y: in (mm)
23.6 x 13.0 (600 x 330)
Table to Spindle Nose Distance: in (mm)
7.0 ~ 14.9 (175 ~ 380)
Max. Workpiece Weight: lb (kg)
220 (100)
Coolant Tank Capacity: gal (L)
Table Height from Floor: in (mm)
29.5 (750)
Actual Measured Circularity (2.0" dia. @8 IPM): in (μm)
0.000039 (1.0)
Spindle Taper
Spindle Air Purge
Air Blast through Spindle
Oil Mist with Collector
Linear Scales X, Y, Z - axes
Heidenhain 0.000002mm Standard
Rapid Traverse Speed: in/min. (m/min.)
590 (1.5)
Cutting Speed (Normal Mode): in/min. (mm/min.)
0.04 - 394 (1 ~ 10,000)
Cutting Speed (GR Super PC Mode): in/min. (m/min.)
590 (1.5)
Dust Collection System
Amano PiE-15 Standard
Machine Weight: lb (kg)
5500 (2500)
Machine Height: in (mm)
85.4 (2170)
Required Floor Space [Machine Unit]: in (mm)
51.2 x 73.5 (1300 x 1867)
Control Unit
Fanuc 31i-A5 Super High-Speed Processor and AI Contour Control II
Power Requirements KVA
200 ~ 220V 12.5KVA
Air Supply
14.1 cu.ft./min @72 psi


For years, tool, die and mold makers have relied on EDM to produce tools in hardened steels that were difficult or impossible to machine. As pressure builds to cut lead times and streamline processes, EDM adds an extra step to the metal cutting process to improve overall productivity.  So when machining directly into hardened steel, roughing and finishing molds and dies on a machining center in one set-up has become increasingly attractive in terms of efficiency.

High-speed machining technology has progressed rapidly over the last few years and is ready to take on this task using high (30,000) RPM spindles, extremely accurate Horizontally Opposed Linear Motor Servo Drive Systems, high-speed machine controllers and advanced cutting tool coatings.  Roku-Roku, a specialty machine tool builder known for making high quality and extremely accurate machines, researched and incorporated all of these technologies into the new larger higher powered (20 HP) Vision 300 model.  The Vision 300 is a machining center designed from the ground up for extremely precise, hard steel machining at high spindle speeds and high traverse rates – “high velocity” machining. Here are some of the features that set the Vision 300 apart.

The Roku-Roku Vision 300 is an exceptionally well-built machine tool coupled with the Fanuc 31i-B5 CNC Controller. Roku’s Super PC III optimizes velocity and acceleration/deceleration through the use of a super high-speed processor and AI Contour Control II, High-Speed processing, Nano Smoothing and Look Ahead Block Expansion.  The combination of high-speed calculation and read ahead control minimizes geometric errors during high-speed contouring of continuous small motion commands.  Super PC III can be set to one of 3 different modes to meet your machining requirements. The Roku-Roku Vision 300 also features Fanuc’s Digital Intelligent Servo System with five-place decimal input and feedback. This combination results in unsurpassed speed and accuracy, even in the most complex, three-dimensional contours consisting of short consecutive line segments or arcs.


  • X-, Y- and Z-Axes Horizontally Opposed Linear Motor Drive System
  • Z-Axis Thermal Growth Compensation
  • Special Precision Roller Type Linear Motion Ways
  • Active H.I.S. (Active Heat Isolation System)
  • Advanced M-Kit (Visual Machine Behavior)
  • Super TMS (Super Tool Measurement System)
  • ASC (Auto Saturation Check Function)
  • Auto Lubrication
  • Full Enclosure
  • Special Way Covers Reduce Motion Resistance
  • 30,000-RPM, 20 HP Integral Motor Spindle
  • Spindle Chiller
  • M&H Super TMS (Tool Measuring System)
  • 68-gallon (260L) Coolant Tank
  • 20-Position Automatic Tool Changer
  • X-, Y- and Z-Axes (2 NANO meter) Linear Scales
  • Mist Collector
  • Oil Temperature Control for Coolant
  • Tool Tightening Block
  • Automatic Power Shut Down Circuit
  • Work Washer Gun
  • Air Purge
  • 10.4-inch Color Monitor
  • Two-Stage Patrol Lamp (Yellow, Red)
  • Manual Handle Feed
  • One Machine Lamp (LED)
  • Tool Box
  • Maintenance Kit
  • Leveling Bolts and Pads

Fanuc 31i-B5 Control Features

  • Super PC III Function (3 Mode Operation)
  • AI Contour Control II, High-Speed processing, Nano smoothing and Look ahead block expansion
  • Editable Data Server with 2GB Program Storage (Flash Card type)
  • Ethernet with TCP/IP Protocol & RS232 Communications
  • 320 Meters Memory (128KB)
  • Custom Macro B
  • Parts Count & Run Hour Display
  • Inch Metric Switching
  • Helical Interpolation
  • Program Restart

Want to learn more?

Click here to contact one of our experts who will gladly answer your questions and help you find the best option based on your needs.


Click here to request technical support, on-site service, training, or for purchasing replacement parts from our large inventory.